Fluke 753 Documenting Process Calibrator
Request a quote
Fluke 753 is a handheld multifunction documenting calibrator with simultaneous source and measurement capabilities for pressure, temperature, and electrical signals.
Product details
| Model | 753 |
| Manufacturer | Fluke |
| Category | Multifunction Calibrators |
| Availability | Made to order |
Description
Overview
The Fluke 753 is a powerful multifunction documenting calibrator that combines sourcing, simulating, and measuring capabilities for pressure, temperature, and electrical signals in a single, rugged handheld device. It features simultaneous source and measurement capabilities, allowing technicians to calibrate, maintain, and troubleshoot instrumentation with ease. The 753 automates calibration procedures, captures data for documentation, and helps meet rigorous standards including ISO 9000, FDA, EPA, and OSHA requirements.
Key Features
- Simultaneous measurement and sourcing of pressure, voltage, current, resistance, frequency, and temperature
- Automatic calibration procedures with as-found/as-left documentation for compliance
- Stores up to one week of downloaded procedures and calibration results for offline analysis
- Advanced options including autostep, custom units, user-entry prompts, switch testing, and programmable delays
- Pressure measurement and sourcing with up to 50 Fluke 700Pxx pressure modules
- Dual display for simultaneous viewing of sourced and measured parameters
- Rechargeable Li-Ion battery with gas gauge indicator for 8+ hours of operation
- Software compatibility with DPCTrack2 and other asset management platforms via USB
- Three-year standard warranty
Applications
- Field calibration of pressure transmitters and sensors
- Temperature sensor and RTD calibration
- Electrical instrumentation testing and troubleshooting
- Automated documentation for ISO, FDA, and OSHA compliance
- On-site repair and maintenance of process instruments
Specifications
| Loop power function | Voltage: Selectable, 26 V Accuracy: 10%, 18 V minimum at 22 mA Maximum current: 25 mA, short circuit protected Maximum input voltage: 50 V DC |
| Step functions | Source functions: Voltage, current, resistance, frequency, temperature Manual step: Selectable step, change with arrow buttons Autostep: Fully programmable for function, start delay, stepvalue, time per step, repeat |
| Operating temperature | -10°C to +50°C |
| Storage temperature | -20°C to +60°C |
| Dust/water resistance | Meets IP52, IEC 529 |
| Operating altitude | 3000 m above mean sea level (9842 ft) |
| Size | 136 x 245 x 63 mm (5.4 x 9.6 x 2.5 in) |
| Weight | 1.2 kg (2.7 lb) |
| Batteries | Internal Battery Pack Li-ion: 7.2 V, 4400 mAh, 30 Wh |
| Battery life | > 8 hours typical |
| Battery replacement | Via snap-shut door without opening calibrator; no tools required |
| Side port connections | Pressure module connector USB Connector to interface to your PC Connection for optional battery charger/eliminator |
| Data storage capacity | 1 week of calibration procedures results |
| 90 day specifications | The standard specification interval for the 750 Series are 1 and 2 years. Typical 90 day measurement and source accuracy can be estimated by dividing the one year "% of reading" or "% of output" specifications by 2. Floor specifications, expressed as "% of full scale" or "counts" or "ohms" remain constant. |
| Agency approvals | CAN/CSA C22.2 No 1010.1-92, ASNI/ISA S82.01-1994, UL3111, and EN610-1:1993 |
| Current DC | 30.000 mA 110.00 mA 0.01% + 5 uA 0.01% + 20 uA 0.015% + 7 uA 0.015% + 30 uA |
| Frequency | 1.00 to 110.00 Hz / 0.01 Hz 110.1 to 1100.0 Hz / 0.1 Hz 1.101 to 11.000 kHz / 0.001 kHz 11.01 to 50.00 kHz / 0.01 kHz 0.05 Hz 0.5 Hz 0.005 kHz 0.05 kHz |
Request a quote
Fluke 753 Documenting Process Calibrator
Response within 24 hours
No obligation
Direct communication